Eldes EKB3 Manuale di Installazione Scaricare il pdf (Pagina 154)

154

154 EN

MANUAL ELDES ESIM264 V3.1

11. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Conguration Tool

software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for

more details.

12. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWD2

closer to alarm system device and bind it again.

13. EWD2 is ready for use.

ATTENTION: Ensure that EWD2 device is properly xed to the wall and the Mounting Point B portrayed in Fig. No. 99 is properly screwed in.

Otherwise, the tamper switch will NOT supervise the back side of EWD2 enclosure (see also 32.11.3. EWD2 Zones and Tampers).

NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again. See

31.11.5. Restoring Default Parameters for more details.

32.11.3. EWD2 Zones and Tampers

Upon successful EWD2 magnetic door contact binding process, the system adds 2 wireless Instant zones. The wireless zones can be set up

to operate under one of the following modes each:

• Zone 1:

• Magnetic door contact – Designed for causing an alarm (by default) if doors/windows are opened when the system is armed.

• External sensor – Designed for causing an alarm (by default) if the wired digital sensor, connected to Z and COM terminals, is

triggered when the system is armed. This mode does NOT operate with Water sensor mode on Zone 2 simultaneously.

• Zone 2:

• Shock sensor – Designed for causing an alarm (by default) if the built-in shock sensor is triggered.

Possible zone mode combinations:

• Zone 1: Magnetic door contact + Zone 2: Shock sensor

• Zone 1: External Sensor + Zone 2: Shock sensor

• Zone 1: Magnetic door contact + Zone2: N/A

• Zone 1: External Sensor + Zone2: N/A

• Zone 1: N/A + Zone 2: Shock sensor

NOTE: Water sensor mode is not supported when EWD2 is used with ESIM264 alarm system.

In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation

on EWD2:

• By tamper switch. EWD2 comes equipped with 2 built-in tamper switches intended for enclosure supervision:

• one located on the front side of the PCB supervising the front cover in case it is illegally opened (see Fig. No. 95).

• the other one located on back of the PCB supervising the back side of the enclosure in case the EWD2 is illegally detached from

the wall (see Fig. No. 95).

Once the enclosure of EWD2 is tampered, the tamper switch will become triggered. This action will be followed by alarm, resulting in

sending an SMS text message and/or phone call to the user. The SMS text message contains the violated tamper number.

• By wireless connection loss. The wireless connection loss between EWD2 and ESIM264 system leads to alarm. The system

identies this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The SMS

text message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.

ATTENTION: The tamper will not operate if both wireless zones are disabled.

For more details on EWD2 zone and tamper conguration, please refer to ELDES Conguration Tool software’s HELP section.

32.11.4. Battery Replacement

1. Open EWD2 enclosure.

2. Remove both old batteries from the battery slots.

3. Insert the 2 new 1,5V Alkaline AAAA type batteries according to the appropriate battery slot positive/negative terminals indicated on

the PCB of EWD2.

4. Batteries replaced.

See 32.11.2. Installation for more details.

1 2 ... 149 150 151 152 153 154 155 156 157 158 159 ... 167 168

Commenti su questo manuale

Nessun commento

Eldes EKB3 Manuale di Installazione Pagina 154

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Eldes EKB3