Eldes EKB3 Manuale di Installazione Scaricare il pdf (Pagina 155)

155

155EN

MANUAL ELDES ESIM264 V3.1

ATTENTION: Only 1,5V Alkaline AAAA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old

batteries with the new ones.

ATTENTION: At least 1 battery must be removed if the device is not in use.

ATTENTION: In order to avoid re or explosion hazards, the system must be used only with approved battery. Special care must be taken

when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble,

heat or incinerate old batteries.

ATTENTION: The system sends an SMS message to a preset user phone number as soon as the battery level runs below 5%.

ATTENTION: The battery status can be monitored in real-time using ELDES Conguration Tool software.

32.11.5. Restoring Default Parameters

1. Remove any battery from EWD2.

2. Press and hold the RESET button.

3. Insert the battery back to EWD2.

4. Hold the RESET button until LED indicator provides several short ashes.

5. Release the RESET button.

6. Parameters restored to default.

32.12. EWS3 - Wireless Indoor Siren

Main features:

• Audio alarm indication by 2 built-in speakers.

• Visual alarm indication by built-in LED indicators: burglary/24-hour/tamper alarm and re alarm indicated in dierent colours.

• 2 tamper switches: for enclosure opening and device detachment from the wall detection.

EWS3 is a wireless indoor device with built-in siren speakers and LED indicators operating with ELDES wireless alarm systems. The de-

vice is designed to notify the user by audio and visual signals in the event of alarm as well as in event of system arming/disarming (Bell

Squawk feature must be enabled). In the event of burglary, 24-hour or tamper alarm, EWS3 will activate the speakers and ash the blue

LED indicators, while in case of a re alarm, the device can ash the red LED indicator (both features require EWS3 Alarm LED and EWS3

Fire Alarm LED parameters to be enabled using ELDES Conguration Tool software or EKB2/EKB3 keypad)

To start using EWS3, it has to be bind to ELDES alarm system by sending a corresponding SMS message or using software ELDES Cong-

uration Tool. Upon successful EWS3 binding process, the system adds one wireless zone and one wireless PGM output. In case of alarm,

the siren provides a sound alarm for one minute. The conguration of this parameter is disabled for EWS3 in order to save the battery

power.

It is possible to connect up to 16 EWS3 devices to ESIM264 alarm system. The maximum wireless connection range is 150 meters (in open

areas).

32.12.1. Technical Specications

32.12.1.1. Electrical & Mechanical Characteristics

Battery Type 1,5V Alkaline AA type

Number of Batteries 4

Battery Operation Time ~18 months*

Wireless Transmitter-Receiver Frequency 868 Mhz

Rangeof Operating Temperatures -25...+55ºC

Humidity 0-90% RH @ 0... +40 °C (non-condensing)

Dimensions 167 x 80 x 34 mm

Wireless Communication Range Up to 30 meters in premises; up to 150 meters in open areas

Compatible with Alarm Systems ELDES Wireless

Acoustic Sound Level ~90 dB measured at 1 m

* The operation time might vary in dierent conditions.

1 2 ... 150 151 152 153 154 155 156 157 158 159 160 ... 167 168

Commenti su questo manuale

Nessun commento

Eldes EKB3 Manuale di Installazione Pagina 155

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Eldes EKB3