Eldes EKB3 Manuale di Installazione Scaricare il pdf (Pagina 67)

67EN

MANUAL ELDES ESIM264 V3.1

19. WIRELESS DEVICES

ESIM264 system can be equipped with a wireless transmitter-receiver module EWT1 (see 32.1. EWT1 - Wireless Transmitter-Receiver)

for system extension capabilities. The module allows the user to easily bind up to 16 ELDES-made wireless devices to the system. This

includes the following:

• EWP1 – wireless PIR sensor (motion detector).

• EWD1 – wireless magnetic door contact.

• EWD2 - magnetic door contact/shock sensor/water sensor

• EWS1 and EWS3 – wireless indoor sirens.

• EWS2 – wireless outdoor sirens.

• EWK1 and EWK2 – wireless keyfobs.

• EW1 – wireless zone and PGM output expansion module.

• EW1B – wireless battery-powered zone and PGM output expansion module.

• EWF1 - wireless smoke detector.

The wireless devices can operate at a range of up to 30 meters from the alarm system unit while inside the building and at up to 150

meters range in open areas. The wireless connection is two-way and operates in one of four available channels at 868MHz non-licensed

frequency range. The communication link between the wireless device and the alarm system is constantly supervised by a congurable

self-test period.

For more details on how to install the wireless devices, please refer to 32. ELDES WIRELESS DEVICES and RADIO SYSTEM INSTALLA-

TION AND SIGNAL PENETRATION manual located at www.eldes.lt/download

19.1. Binding, Removing and Replacing Wireless Devicess

When the wireless device is switched ON, it will initiate the data transmission to the system within its wireless connection range. In order to

optimize battery power saving of the wireless device, the data transmission periods vary by itself while the device is switched ON, but still

unbound. The data transmission period of the wireless devices when the alarm system is switched OFF or if the wireless device is unbound

or removed is as follows:

• EKB3W, EW1, EW1B, EWP1, EWS1, EWS2, EWS3, EWF1:

• First 360 attempts after the device startup (reset) - every 10 seconds.

• The rest of attempts - every 1 minute.

• EWD1, EWD2:

• First 360 attempts after the device startup (reset) - every 10 seconds.

• The rest of attempts - every 2 minutes.

Once the wireless device is bound, it will attempt to exchange data with ESIM264 system. Due to battery saving reasons, all ELDES wireless

devices operate in sleep mode. The data exchange will occur instantly if the wireless device is triggered (zone alarm or tamper alarm) or pe-

riodically when the wireless device wakes up to transmit the supervision signal, identied as Test Time, to the system as well as to accept

the queued up command (if any) from the system. Example: The alarm occurred at 09:15:25 and the system queued up the command for

EWS2 siren to start sounding. By default, Test Time value of EWS2 siren is 7 seconds, therefore EWS2 siren will sound at 09:15:32.

By default, the Test Time period is as follows:

• EWD1: every 60 seconds.

• EW1, EWD2, EWP1, EWF1: every 30 seconds.

• EW1B: every 20 seconds.

• EWS1, EWS2, EWS3: every 7 seconds.

To set a dierent Test Time value, please refer to the following conguration method.

Set Test Time

Cong

Tool

This operation may be carried out from the PC using the ELDES Conguration Tool software.

1 2 ... 62 63 64 65 66 67 68 69 70 71 72 ... 167 168

Commenti su questo manuale

Nessun commento

Eldes EKB3 Manuale di Installazione Pagina 67

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Eldes EKB3